"Waterproof" is one of the most overused words in gear marketing, and "crushproof" and "dustproof" are not far behind. For anyone buying a case to protect valuable or mission-critical equipment, the words matter less than the standards behind them. This guide unpacks the ratings you will see on a quality protective case so you can read a spec sheet with confidence. Optimal Cases and Lights Inc works with these ratings every day, and the short version is that a reputable case tells you exactly how it was tested rather than leaving you to guess.
IP ratings: the two digits that matter
The most widely used standard is the IP, or Ingress Protection, code. It looks like "IP67" and the two digits are separate claims.
The first digit: solids and dust
The first digit rates protection against solid objects and dust on a scale from 0 to 6. A 5 means dust-protected, with limited ingress that does not interfere with operation. A 6 means fully dust-tight, with no ingress at all. For field gear that lives around sand, grit, and sawdust, a 6 is what you want.
The second digit: water
The second digit rates water resistance, typically from 0 to 8. A 7 means the enclosure withstands temporary immersion to one metre for thirty minutes. An 8 means it handles continuous immersion under conditions the manufacturer specifies. A sealed case rated IP67 is therefore both fully dust-tight and able to survive a short dunk, which is why that rating is common on quality cases. You can see sealed designs across the Pelican Protector cases range.
Why an O-ring and a purge valve do the heavy lifting
A high IP rating is only as good as the seal that creates it. A continuous O-ring gasket around the lid is what keeps water and dust out, and it needs to be clean, intact, and free of grit to seal properly. Most serious cases also include an automatic pressure equalization valve, a small vent that lets air pressure balance across changes in altitude or temperature while still blocking water. Without it, a case sealed at sea level can be hard to open after a flight, or can draw moisture in as it cools. The Pelican Storm series pairs this sealing approach with its press-and-pull latch design.
"Crushproof" and impact resistance
"Crushproof" has no single consumer standard the way IP ratings do, so treat the word as shorthand for a robust, load-bearing shell rather than a guarantee. What actually protects your gear is the combination of a thick-walled polymer body, reinforced corners, and strong latches that keep the lid closed under load. Ask what the case is moulded from and how the latches are rated, not just whether the brochure says crushproof.
Impact ratings are different from water ratings
Drop and impact resistance is a separate property from water or dust sealing. A case can be beautifully watertight and still transmit shock to the contents if there is no internal cushioning. That is why foam, padded dividers, or a suspension system inside the case matter as much as the shell. The rating protects the box; the interior protects the gear.
Weight versus protection: a real trade-off
More protection usually means more material and more weight, which is where lighter lines come in. The lighter Pelican Air cases are engineered to hold a strong sealed rating while shedding weight compared with heavier-duty cases, which matters when you are paying airline overage or carrying a case all day. The point is to buy the lowest weight that still meets the protection level your gear genuinely needs, rather than over-building and hauling the penalty everywhere.
How to read a case spec sheet
When you compare two cases, line up four things: the IP rating written in full, whether a pressure equalization valve is included, what the shell is made from, and how the interior is cushioned. A case that states all four clearly is telling you it was engineered to a standard. A case that only says "waterproof and tough" is asking you to take its word for it. If a spec sheet leaves you unsure, the staff at Optimal Cases and Lights Inc can translate the ratings into plain language for the gear you actually need to protect.
Frequently Asked Questions
What does IP67 actually mean?
The 6 means the case is fully dust-tight with no ingress. The 7 means it can survive temporary immersion in water to one metre for thirty minutes. Together they describe a sealed case that keeps out both dust and a short soak.
Is "crushproof" a real certified rating?
Not in the way IP ratings are. It is a marketing term for a strong, load-bearing shell. Judge the actual build by the shell material, corner reinforcement, and latch strength rather than the word alone.
Why do sealed cases have a small vent or valve?
That is a pressure equalization valve. It lets internal and external air pressure balance during altitude or temperature changes while still blocking water, so the case does not become hard to open or draw in moisture as it cools.
Does a high water rating protect my gear from drops?
No. Water and dust sealing is separate from impact protection. You also need internal cushioning such as foam or padded dividers to absorb shock, because the shell protects the case while the interior protects the contents.
Do I need to maintain the seal?
Yes. The O-ring gasket only seals when it is clean and undamaged. Wipe away grit, check it for nicks, and keep it seated so the rated protection actually holds up over time.